I would like to pass along my experience with the Ruger 556 so far .
Out of the box ( nice packaging , Nice case ) I liked what I saw.
I gave it a bath and a good once over. My first disappointment was the
upper to lower fit was very sloppy , for being built by Ruger from the ground up I expected
a nice tight or at least snug fit. I was happy with the rest of the fit and finish.
Before I even fired the first round I reconfigured it to my favorite accessories
and a new Nightforce NSX 2.5 x 10 x 32 I was itching to mount,
I chose my favorite high 30 mm rings from TSR " W " that are just high enough
to accommodate the nice Iron sights Ruger includes , under the scope for backup.
I also installed US optics fold away sprit level , Power custom Oversize mag release,
Ace Socom 4 long stock, Daniels Defense 1 o'clock mount and a burris Fastfire II,
a Versapod picatiny stud w/ a bench rest model that adjusts from 7 to 9 inches,
I installed the rail protectors of which one was missing ( Ruger was quick to send a replacement )
and Graphite forward pistol grip by SOG Armory from Brownelles
and I swapped out the Hogue grip for my favorite Ergo grip,
and Last but not least a DPMS / Miculek muzzle brake. Removing the factory flash
hider was tougher than I expected . Ruger customer service recommended
a spanner wrench. I clamped hard on the bbl with a rubber padded insert
made from conveyor belting and not having a spanner wrench of the correct size
I wrapped it with GO rilla tape ( 4 layers ) and grabbed my trusty Ridgid pipe wrench and
and gave steady pressure till it came loose. ( whew ) and once the tape
was removed and a little WD 40 to get the tape goo of i was pleased to see
not even a scratch.
Oh I almost forgot a Jard 3# trigger to replace the 12+ pound factory trigger.
My first time out to the back yard only gives me 25 yards to get close
on the settings for both the NSX and the FFII
it ran fine for 10 rounds , so off to clean it up during the bbl break-in period.
My first trip to the real range had me thinking I would like to wrap it around a tree
as the first 8 rounds I tried went " Click "
I thought maybe a problem with the trigger or light hammer strikes as there was barely a dimple
in the primmer . So I swapped the lower for another and found the same issue.
My next thought turned to the Firing pin and wondered if it was gummed up.
Yup that was it, it was so stiff It took my leatherman to get it out and I
found what ever Ruger packed in there was like glue in the 28 Degree F Morning here
in Northern WI so after I cleaned it up and a few Qtips with RemOil I was back in business.
I fine tuned the scope @ 100 and
shot a quick 5 shot group @ 100, about an inch.
The new velocity reticle from Nightforce has a top crosshair for 100
the center for 200 and then 300 out to 600 and halfway hashmarks in between
as well, plus instant windage marks to boot. ( SWEET )
http://www.nightforceoptics.com/RETICLES_O...l.html#velocity
I called Nightforce CS before I ordered and double checked the recommended reticle selection
for my favorite load ( 50 Gr. Vmax or Sierra BK over 24.2 Gr of H322 = 3140 fps )
I also found the slick program right on there web site to help in choosing the right
reticle.
I engaged the 300 yard target by raising up to the 300 yard mark
and fired a quick string of 9 shots . The scope is crystal clear and
the 3.75 in red dot I was shooting @ was easy to see and easy to hold
for a good release using the Versapod in front, and my fist under the pistol
grip for rear support. I was very pleased to see the group when I drove down to the target.
2.3 in for 9 shots ( this happened to be the sierra's but I get great results with both. )\
Looks like a keeper so far.
Any ??? drop me a note
SWandME
Out of the box ( nice packaging , Nice case ) I liked what I saw.
I gave it a bath and a good once over. My first disappointment was the
upper to lower fit was very sloppy , for being built by Ruger from the ground up I expected
a nice tight or at least snug fit. I was happy with the rest of the fit and finish.
Before I even fired the first round I reconfigured it to my favorite accessories
and a new Nightforce NSX 2.5 x 10 x 32 I was itching to mount,
I chose my favorite high 30 mm rings from TSR " W " that are just high enough
to accommodate the nice Iron sights Ruger includes , under the scope for backup.
I also installed US optics fold away sprit level , Power custom Oversize mag release,
Ace Socom 4 long stock, Daniels Defense 1 o'clock mount and a burris Fastfire II,
a Versapod picatiny stud w/ a bench rest model that adjusts from 7 to 9 inches,
I installed the rail protectors of which one was missing ( Ruger was quick to send a replacement )
and Graphite forward pistol grip by SOG Armory from Brownelles
and I swapped out the Hogue grip for my favorite Ergo grip,
and Last but not least a DPMS / Miculek muzzle brake. Removing the factory flash
hider was tougher than I expected . Ruger customer service recommended
a spanner wrench. I clamped hard on the bbl with a rubber padded insert
made from conveyor belting and not having a spanner wrench of the correct size
I wrapped it with GO rilla tape ( 4 layers ) and grabbed my trusty Ridgid pipe wrench and
and gave steady pressure till it came loose. ( whew ) and once the tape
was removed and a little WD 40 to get the tape goo of i was pleased to see
not even a scratch.
Oh I almost forgot a Jard 3# trigger to replace the 12+ pound factory trigger.
My first time out to the back yard only gives me 25 yards to get close
on the settings for both the NSX and the FFII
it ran fine for 10 rounds , so off to clean it up during the bbl break-in period.
My first trip to the real range had me thinking I would like to wrap it around a tree
as the first 8 rounds I tried went " Click "
I thought maybe a problem with the trigger or light hammer strikes as there was barely a dimple
in the primmer . So I swapped the lower for another and found the same issue.
My next thought turned to the Firing pin and wondered if it was gummed up.
Yup that was it, it was so stiff It took my leatherman to get it out and I
found what ever Ruger packed in there was like glue in the 28 Degree F Morning here
in Northern WI so after I cleaned it up and a few Qtips with RemOil I was back in business.
I fine tuned the scope @ 100 and
shot a quick 5 shot group @ 100, about an inch.
The new velocity reticle from Nightforce has a top crosshair for 100
the center for 200 and then 300 out to 600 and halfway hashmarks in between
as well, plus instant windage marks to boot. ( SWEET )
http://www.nightforceoptics.com/RETICLES_O...l.html#velocity
I called Nightforce CS before I ordered and double checked the recommended reticle selection
for my favorite load ( 50 Gr. Vmax or Sierra BK over 24.2 Gr of H322 = 3140 fps )
I also found the slick program right on there web site to help in choosing the right
reticle.
I engaged the 300 yard target by raising up to the 300 yard mark
and fired a quick string of 9 shots . The scope is crystal clear and
the 3.75 in red dot I was shooting @ was easy to see and easy to hold
for a good release using the Versapod in front, and my fist under the pistol
grip for rear support. I was very pleased to see the group when I drove down to the target.
2.3 in for 9 shots ( this happened to be the sierra's but I get great results with both. )\
Looks like a keeper so far.
Any ??? drop me a note
SWandME