Forums
New posts
Search forums
What's new
New posts
New media
New media comments
Latest activity
Media
New media
New comments
Search media
Members
Registered members
Current visitors
Log in
Register
What's new
Search
Search
Search titles and first posts only
Search titles only
By:
Registered members
Current visitors
Menu
Log in
Register
Install the app
Install
Members
JavaScript is disabled. For a better experience, please enable JavaScript in your browser before proceeding.
You are using an out of date browser. It may not display this or other websites correctly.
You should upgrade or use an
alternative browser
.
Help Support Ruger Forum:
AZ10X
Bearcat
·
From
Sun City, AZ
Joined
Feb 28, 2024
Last seen
Wednesday at 10:47 PM
Messages
25
Reaction score
19
Find
Find content
Find all content by AZ10X
Find all threads by AZ10X
Latest activity
Postings
About
Post areas
AZ10X
reacted to
loaded round's post
in the thread
Screw size info for you
with
Like
.
The Brownell's Screw Chek'r works perfectly and is a great tool. I've also had mine for over 10 years and it's been a lifesaver more...
Sunday at 1:10 AM
AZ10X
replied to the thread
Can a new front sight be "blued" or darkened prior to install?
.
Use some clear enamel in mat finish to protect the existing coating.
Sunday at 1:09 AM
AZ10X
replied to the thread
Primer hole in brass
.
Starline consistenly makes their flash holes larger.
Apr 17, 2024
AZ10X
replied to the thread
44 special load in 44mag
.
Just buy some .44 Special brass and follow the published load data. Problem solved!
Apr 17, 2024
AZ10X
replied to the thread
1977 M77 220swift
.
Get a new unfired, un-sized case. Check the length. Seat a bullet short of the lands. If it is hard to chamber and extract you have a...
Apr 17, 2024
AZ10X
replied to the thread
1977 M77 220swift
.
If this is the gauge, with the correct insert, that you are using your are fine. https://www.hornady.com/headspace-bushings#!/ However...
Apr 16, 2024
AZ10X
replied to the thread
1977 M77 220swift
.
Sizing the brass has reduced the neck OD. Measure the neck OD on the un-sized brass. If it is larger than .260 that is the problem...
Apr 16, 2024
AZ10X
replied to the thread
1977 M77 220swift
.
Logically, there can only be two causes of your problem. First, it can be your rifle. If it is a factory Ruger rifle you can rule out...
Apr 15, 2024
AZ10X
replied to the thread
1977 M77 220swift
.
The Swift is one of the rare calibers that needs to be full length sized after every firing. Do you have any fired cases from when you...
Apr 15, 2024
AZ10X
replied to the thread
New die doesn’t give enough shoulder bump
.
You were probably sent a die based on a reamer other than what was used to chamber your rifle. I had problems with Redding in the past...
Mar 20, 2024
AZ10X
replied to the thread
Primer hole in brass
.
Small primer flash hole standard size is .062 and large primer is .080
Mar 20, 2024
AZ10X
replied to the thread
Just done 6 rounds of 30/30
.
Mar 20, 2024
AZ10X
posted the thread
For Sale
Ruger 77V varmint taper barrel for sale
in
Classifieds Section
.
Chambered in .220 Swift 25 1/2" 1-14 Bore scope shows throat, bore and crown to be in very good condition very few minor marks in...
Mar 17, 2024
AZ10X
replied to the thread
Following up on "old powder"
.
The only difference in burn rate that I am aware of was with pre 1973 IMR 4831 which was previously military surplus 4831. Actually the...
Mar 1, 2024
AZ10X
replied to the thread
Polymer jacket ammo
.
I rarely buy factory loaded ammo. I have been using powder coated semi wadcutter in pistols and revolvers for target use...
Mar 1, 2024
Loading…
Loading…
Loading…
Latest posts
T
Ruger PCC Rebuild
Latest: TheKid
Today at 3:24 AM
Ruger Photos & Gallery
Repairing a box
Latest: jimbo1096
Today at 2:14 AM
Ruger & Other Firearm Collecting
Charter Arms 44
Latest: buckeyeshooter
Today at 12:58 AM
Concealed Carry Central
Members
Top