F/S: (17 May) NM SS Grip Frames, Hammers, Triggers, Hogue

[RatCat454]

Edited 17 May, update pics, more items.

Have several stainless NM Blackhawk, Single Six, Single Seven (standard like XR3) grip frames, with factory grip panels as delivered from Ruger. Most were removed from new guns, some have the frame extensions, some do not. All are stainless standard grip frames or square trigger guard Super Blackhawk,...no Bisley, Hunter, or Birdshead, . All are 1/2 inch back strap, no 7/16, no internal locks. Grip frames include the five Ruger OEM stainless screws. More pics available on request.

Grip frame without grip panels, $100 delivered using USPS, CONUS. Grip frame with grip panels, $120 delivered, USPS, CONUS. PayPal available.

The dragoon square trigger are early Blackhawk that previous owner started to fit to early NM Single Six, thus on a larger frame Blackhawk will be narrow in the bottom trigger area and short at the hammer pivot radius. Priced at $80 with the 5 screws shipped, $70 shipped, no screws.

Also, hammers and triggers (standard), rubber Hogue suitable to the standard frames pictured, Power Custom half-cock kits. Ask for a prices if not posted.

I am not a gunsmith, business, or commercial venture but a long time Ruger owner attempting to get a handle on hoarded spare parts.

 

[Hondo44]

Welcome to the forum.

Do you have any 7/16" thick XR3 size from a New Vaquero or NM Flat Top Blackhawk?

Thx,
Jim

 

[RatCat454]

These are all 1/2 inch.

 

[LAH]

I purchased a grip frame, grips, & screws. They arrived today well packed & in excellent condition. I'm happy.

 

[RatCat454]

LAH, Thanks for the positive feedback!

 

[Gene]

RatCat, do you happen to have a Super Blackhawk hammer? I want to convert my stock NM Blackhawk hammer to a Super Blackhawk hammer. Thanks.

 

[Galaxiedan]

Details on the cylinder please, looking for a 45lc to fit my new model Vaquero.

 

[RatCat454]

The cylinder is a NM large frame blue 9mm.

It does have an issue that I will ask about in the gunsmith section for a remedy. A previous unknown owner has trimmed several thousandths from the front base pin area (possibly to shim to minimize cylinder end shake?).

 

[Redington Slim]

What is the price for the Power Custom half cock kits, and what do they fit/what models are they for?

 

[RatCat454]

What is the price for the Power Custom half cock kits, and what do they fit/what models are they for?

Stainless steel, standard hammer and trigger, small frame NM 22/32/327 Single Six based guns, $130 each delivered, all three for $330 delivered.

Have these posted separately before realizing better to list all in one thread:

http://www.rugerforum.com/phpBB3/viewtopic.php?f=41&t=265991

I have installed the Power Custom kits in over 20 guns. Probably like 90% were drop in. The remainder required a slight tweak at the cylinder pawl lower tooth (couple of passes with a safe edge fine cut extra narrow file done with pawl in the gun, lightly wedge pawl out with a pick, use masking tape to protect from wandering file) to allow the hammer to set at cylinder lock. Fit and finish seems better than OEM Ruger.

 

[LAH]

Mounted the grip frame & stocks today. Everything is good.

 

[RatCat454]

Mounted the grip frame & stocks today. Everything is good.

Thanks for the feedback!

 

[Gator89]

My grip frame arrivedo today, not a scratch or scuff on it. Excellent transaction.

 

[RatCat454]

My grip frame arrivedo today, not a scratch or scuff on it. Excellent transaction.

That one was from a personal gun, NIB take-off.

The Post Office quoted Thursday, delivered early!

For others who may be interested, 5 grip frames left. Started with 11.

 

[RatCat454]

Updated pictures, added SBH hunter hammers to the fray.

 

[jkelliott]

I live in Elizabethton, tn.
I may want 9mm cylinder. Are you close to my area

 

[RatCat454]

I live in Elizabethton, tn.
I may want 9mm cylinder. Are you close to my area

I am near Wartburg, TN. If you are up near the Tri-Cities, Cherokee National Forest, we are about 160 miles apart. Could use the US Postal Service...

Concerning the cylinder, looks like a .025" spacer shim would do. McMaster has 'em in various thicknesses, .250 ID, .375 OD, stainless, for a couple of dollars.

 

[jkelliott]

Do you have dimensions and a price with shipping?

 

[jkelliott]

Yes I'm 15 minutes from Bristol speedway.

 

[dullknife44]

Good evening,

At 73 years young, and blessed with, among other challenges, a nasty tremor, never-the-less, and an old (heavy on the "old") rifleman (to-be-read, not a handgunner), still got that itch, right smack dab in the middle of these ole' bones back. How's that for a "run-on" sentence, Miss Pruitt, come out, come out, where ever you are, but I digress.
As I was saying, this itch is for a custom six-shooter (can't count no further with-out takin' both boots off, then cain't take the smell). So then I spied your ad and Jim Crackedee, you jest might have what I'm a hankerin' fer. Now if only I kniw what all thet was!!
Seriously, and I jest have a horrible time bein' that way -- ain't no fun - - I would like to have a custom Ruger single action built up on an action suitable for a .327 Fed. Mag. Know I need the frame and fire control mechanisms, do not need barrel, stocks, or barrel. Can you reel in this "red bait" and sell me what I need to drop ship to my "revolversmith"?
Hope you've had a good day, and I figure any day God has given us is good, just a question of perspective. God Bless

dullknife