Eotech on a SBH Hunter
- Thread starter kelbro
- Start date
Help Support Ruger Forum:
Register to hide this ad
contender
Ruger Guru
I think Weigland makes one that fits in the screw holes where the rear sight goes. Check them first.
JesterGrin_1
Single-Sixer
- Joined
- Aug 15, 2009
- Messages
- 129
Look HERE http://www.rugerforum.com/phpBB/viewtopic.php?t=63634 And yes it is a Weigland base. 
And instead of the Eotech you should look into the UltraDot West Line of Red Dots.
And instead of the Eotech you should look into the UltraDot West Line of Red Dots.
JesterGrin_1
Single-Sixer
- Joined
- Aug 15, 2009
- Messages
- 129
contender":2tgvhjym said:
Contender he is talking about the HUNTER
contender
Ruger Guru
Duhh, I feel like a dunce as I was seeing Super Blackhawk,, and didn't "see" the hunter part,,,,! (Picture me wearing a dunce hat sitting in a corner.)
Blue, so you can remove the screws. Red requires a lot of heat to remove screws. Clean ALL threads before using.
Eric
Eric
Three44s
Single-Sixer
+1 for Jack's bases!
+1 for my Bushnell holosight on a RH!
Your Eotech will serve you well. Just remember to shoot it the way you sighted it in. One eyed or two.
Three 44s
+1 for my Bushnell holosight on a RH!
Your Eotech will serve you well. Just remember to shoot it the way you sighted it in. One eyed or two.
Three 44s
JesterGrin_1
Single-Sixer
- Joined
- Aug 15, 2009
- Messages
- 129
Go with Blue
I did however use Red on the screw for my ejector rod housing. Blue just would not hold.
But to be fair my loads were pretty stout I think. I was shooting a 300Gr Cast Bullet GC with 21.O Gr of H-110. And even though they shot very well I just did not wish to have to carry a screw driver kit with me all the time lol.
So right now I am working with an old Ideal 431244 SWC GC with 23.OGr of H-110. But when I have more time like after the next few days I am also going to try 23.5Gr of H-110. And the reason I will have to wait is I am going dove hunting in the morning and hope to find a HOG get with in range lol. I just ran out of time too darn fast for further testing.
I did however use Red on the screw for my ejector rod housing. Blue just would not hold.
But to be fair my loads were pretty stout I think. I was shooting a 300Gr Cast Bullet GC with 21.O Gr of H-110. And even though they shot very well I just did not wish to have to carry a screw driver kit with me all the time lol.
So right now I am working with an old Ideal 431244 SWC GC with 23.OGr of H-110. But when I have more time like after the next few days I am also going to try 23.5Gr of H-110. And the reason I will have to wait is I am going dove hunting in the morning and hope to find a HOG get with in range lol. I just ran out of time too darn fast for further testing.
flatgate
Hawkeye
JG-1,
I'd be a little cautious with your SWC loads. Most SWC's seat deeper in the case than do the LBT's. I don't know much about them, to be honest, but just thought I'd toss out my thoughts.....
Oh, and I think you're perhaps a bit light on your powder charge for that 300 grain bullet....
Again, JMHO,
flatgate
I'd be a little cautious with your SWC loads. Most SWC's seat deeper in the case than do the LBT's. I don't know much about them, to be honest, but just thought I'd toss out my thoughts.....
Oh, and I think you're perhaps a bit light on your powder charge for that 300 grain bullet....
Again, JMHO,
flatgate
JesterGrin_1
Single-Sixer
- Joined
- Aug 15, 2009
- Messages
- 129
I got the load for the SWC 431244 or now it is called the 429244 here. http://www.lasc.us/FryxellMarlin1894.htm And yes it is 1/2 Gr light.
The 300Gr HP GC sits a bit deeper than the Lee 310Gr GC. I know the magic number is 21.5Gr of H-110 or W-296. But I found the Lee to shoot best from my Marlin 1894 with 21.OGr of H-110.
You can read up on the 300GR HP GC I am using here. http://castboolits.gunloads.com/showthr ... t=44%2F444
The 300Gr HP GC sits a bit deeper than the Lee 310Gr GC. I know the magic number is 21.5Gr of H-110 or W-296. But I found the Lee to shoot best from my Marlin 1894 with 21.OGr of H-110.
You can read up on the 300GR HP GC I am using here. http://castboolits.gunloads.com/showthr ... t=44%2F444
Similar threads
