35 Remington Brass and Dies Found alll but bullets

[Stumps13]

I have been sent on a mission to find 35 Remington components.
Any help for the following would greatly appreciated.

1. 35 Remington Brass either new or once fired

2. 35 Remington Die set new or used

3. 180 gr FLAT NOSE bullets

Thank you ion advance.
Stumps

 

[Chuck 100 yd]

When I was searching for .35 Rem. brass, I found it on eBay. Dies are available new. You may have a little problem finding bullets though. Good luck.

 

[Clovishound]

Here are some 190 grain hard cast flat nose.

http://www.midwayusa.com/product/20...190-grain-lead-flat-nose?cm_vc=ProductFinding

Plenty of factory ammo available on the web that will give you brass once fired.

 

[Jimbo357mag]

You can use 180gr 357mag bullets in the 35 Remington. The Hornady 180gr XTP or similar would work well I think.

http://www.midwayusa.com/product/552814/hornady-xtp-bullets-38-caliber-357-diameter-180-grain-jacketed-hollow-point-box-of-100

http://www.midwayusa.com/product/1988218433/cast-performance-bullets-38-caliber-358-diameter-180-grain-lead-wide-flat-nose-gas-check

http://www.midwayusa.com/product/185446/sierra-tournamentmaster-bullets-38-caliber-357-diameter-180-grain-full-profile-jacket-box-of-100

http://www.midwayusa.com/product/424229/hunters-supply-hard-cast-bullets-35-remington-35-whelen-358-diameter-190-grain-lead-flat-nose

35 Remington dies.

http://www.midwayusa.com/find?sortby=1&itemsperpage=20&newcategorydimensionid=11982

35 Remington Brass.

http://www.midwayusa.com/find?sortby=1&itemsperpage=20&newcategorydimensionid=20208

 

[sandman228]

dies are available new at midway .you might get lucky and find a used set for a lower price on e bay .ive also bought brass from midway but its not cheap . I got lucky and came across a few hundred once fired at a good price on a local classified .as for the 180 gr flat nosed bullets your looking for I know speer makes or used to make them . I came across some at a local gunshop a while back as new old stock they were sitting on his shelf since the 1990's when I saw he only wanted 17$ per box I bought all 3 boxes he had . i use them sparingly ,for a plinking load I cast a .358 195 gr lrn bullet from a lyman mold and load it over herco powder ,its a fun plinker . I also wanted to mention ive never tried this myself but ive heard of guys resizing/reforming 308 brass into 35 rem . I don't know what all is involved in it though

 

[djw54]

I see the bullets and dies questions addressed above, I just purchased same from Midway also.
For brass, there's a gent over on castboolits that does form 35 Rem from 308, at a very reasonable price, esp since 35 Rem brass is rare and expensive. Good looking brass, haven't loaded any yet though.
The only hiccup in using this brass is that you need a 308 shell holder, as the rim dimensions are slightly different.

 

[Chuckbuster II]

Stumps
If you are still looking drop me a PM
Kevin

 

[langenc]

Anyone want to swap some 35 Remington brass, pickups, for 44 Magnums??

Im not sure how many 35s I have. Ill check the loading shed next time Im out that way. Id guess at least 50..

Rearranged some brass today--about 75, 35 Rem cases.

Have some 338 Mag, 350 Rem Mag and lots of several 7mm Mag calibers. Could get rid of all of em. What do you need?

 

[langenc]

If the one shooter that contacted me would email I think we can do a deal. I replied but the reply cant be delivered..