medium frame 41 Mg.?
- Thread starter 5of7
- Start date
Help Support Ruger Forum:
Just went today through whole thread and found this post. If Lipseys or any other distributor has Ruger revolvers sitting on the shelves, could they put guns on sale and post on this forum what they have? I've seen on another forums section for distributors and dealers. They regularly post what they have on sale and what they are going to get. Also, they regularly communicate with forum folks for feedback and suggestions.Robb Barnes said:
smith1961
Blackhawk
Chief said:
They already have:
https://www.deguns.net/ruger-blackhawk-41-rem-mag-4-62--stainless-6rd-4031/p
https://www.arkansasonline.com/news/2018/jan/07/bucking-broncos-20180107/
Well, ok I did forget about the hunter model, but it is the only stainless steel 41 mag thatsmith1961 said:
i can find on Rugers web site. If they made some distributors models, they do not seem to still be available.
Thanks for the info though, at least I know what to look for now.
smith1961
Blackhawk
Chief said:
Yeah there are 5.5 Bisley SS blackhawks still around from a run last year or so.......... 8)
smith1961
Blackhawk
Onty said:Talking about Blackhawk stainless 41 Magnum, with 4-5/8" barrel:smith1961 said:
Did Ruger ever make same revolver with 5.5" barrel?
Yes but as a Bisley
Here you go, I just listed this one for sale in the classifieds.
smith1961
Blackhawk
That is (was) an awesome gun Robb. Just shows that a medium frame .41 works and sells every day of the week. Now if we could get a distributor to make this, or even a Vaquero I could go to my grave content.
:shock:
:shock:
Hondo44
Hawkeye
Too easy to make one or have one made rather than risk going to your grave discontented!
bigbill
Single-Sixer
Terry T said:Dropped by a local shop this afternoon - very clean S&W model 58 still there - been there for a couple of months now. A bit pricy but still .... nice piece, if a bit heavy for 'carry'. Not all THAT big.
Point is...folks aren't scrambling to buy it.
Terry T
I got tired of looking for RedHawks in 357 mg & 41 mag. My dealer had new s&w on clearance for $699. The m58 in nickel was $699, the m57 / 6" barrel in nickel was $699. Couldn't pass that up. Found s&w m28/m27-2 357. Soon after the RedHawks showed up with 5.5" barrels in stainless. The s&w m58 / 4" barrel handles awesome. I didn't like shorter barrels under 5.5" but the heavier S&W N frame with a 4" barrel in 41 mag handles fine. Any big gun I shoulder holster anyway. I been a ruger fan for about 48 years now.
dixie884
Blackhawk
It is somebody's birthday, so bump for a good Idea............
USAFA71
Bearcat
While a fan of the 41 magnum, I have the stainless Blackhawk Hunter, and the 5.5" stainless Bisley to go with the Marlin 1894FG. With full magnum loads I would prefer as much weight as possible since I am getting old and no longer enjoy recoil. But a lightweight 41 Special would be perfect for everyday use with a 210-230 gr SWC/WFN at 1000fps(+/- 100fps). I could take it in either SA or DA, as long as it was a 41! While a factory option would be nice, I may have to go custom with either a Bisley Blackhawk or GP-100 as the chassis. If Lipsey's or someone else can do a "special" run(pun intended), I would definitely order one. Prefer stainless but blued is fine.
dixie884
Blackhawk
I wish Ruger would go partners with Speer or Hornady and bring out the ".41 Ruger" based on the specs of the Star-line .41spl brass loaded with a 200 to 210gr bullet loaded to 17,000psi. Then they could chamber it in the mid-frame SA platform and the GP100 in a 6shot cylinder. Of course that will probably have to wait til there is not a back log on orders from their sold out factories.............
What he said!
