What Would You Do? Updated 10/25/21

In This Section We Will Discuss Proper Methods of Maintenance & Repair of Ruger Made Firearms.

Moderator: Moderators

Post Reply
professor_cassidy
Bearcat
Posts: 60
Joined: Sun Sep 07, 2008 7:45 pm
Location: Virginia

What Would You Do? Updated 10/25/21

Post by professor_cassidy »

I recently purchased a Ruger Blackhawk Lipsey’s special run stainless steel Bisley
45 Colt/45 ACP convertible 3.75” barrel. It was lightly used, I don’t think that the
45 Colt cylinder had ever been fired. I believe it had had at least 2 prior owners.
The pictures I saw looked good so I bought it as it was the exact gun I was looking
for (it was expensive!).

I got it home from the transfer dealer and it had the heaviest trigger I’d ever had
on a Ruger in 46 years. Decided to do a “Poor Boy’s” trigger job by releasing one
of the legs on the trigger return spring. Went to take off the grips to release the
leg, and the grip screw was so tight you would have thought it was tightened with
an impact wrench. Got the screw out and grips off and released one of the legs.
Trigger was now much better but now had Transfer Bar pinch (grrrr!). Took it out
the next day and it shot fine with both 45 Colt and 45 ACP cylinders.
Except for the pinch.

Well I read up on transfer bar pinch and decided to take the gun down and stone
down the transfer bar and while I had it apart to install a Wolff’s 30oz trigger
return spring like I have on several other Ruger single actions. Started taking
the gun apart and discovered that the upper left Allen head screw had no head
and the screw was flush with the frame it had been broken off I believe when the
gun was assembled at Ruger (argggghhh!). When I went to take out the long grip
screw that fits in the trigger pin groove it appeared that when it was installed that
what ever power tool is used had slipped and gouged the grip frame some.

Does anyone know if Ruger actually uses power tools when doing final assembly?

Well I got the gun disassembled and stoned the transfer bar some then
reassembled the gun with the 30oz trigger spring. Unfortunately the transfer
bar pinch was the same or worse. So it will need to be taken apart again to file/
stone the transfer bar some more (I have a spare on hand just in case). I shot the
gun again after the above work and it shot fine, except for the pinch.

My question is(finally!) would you send the gun back to Ruger to have them attempt
to remove the broken screw knowing that if they screwed it up that they might then
junk the gun and I wouldn’t be able to get the exact replacement (this has happened
to me twice before). Or should I see if one of my local yokel gunsmiths
could remove the broken screw without screwing it up. Or should I just keep
shooting the gun with 4 grip screws instead of 5, probably wouldn’t shoot anything
hotter then 45 Colt 255 SWC @ 1,000 fps or 45 ACP 230 +P.

I am very leery of sending the gun to Ruger based on my past experience. Equally
leery of any local gunsmiths.

What do you think I should do?
Last edited by professor_cassidy on Mon Oct 25, 2021 2:38 pm, edited 1 time in total.
NikA
Buckeye
Posts: 1272
Joined: Sun Nov 02, 2014 11:10 am
Location: Yrisarri, NM- high in the Manzanos

Re: What Would You Do?

Post by NikA »

First let me say that I haven’t had your negative experience with the mothership, so my first impulse would be to send the gun in to Ruger.

If that were not an option, I would look at drilling out the broken screw with a left hand drill. This is not difficult to do with a drill press that has a reversible motor and the appropriate drill bits. If I were not confident in my ability to do it myself, I'd contact a local machine shop; they deal with this sort of issue all the time.

Last resort would be a local gunsmith; IME they're either under qualified or have an inflated sense of the value of their services (and not infrequently both), so I rarely end up dealing with them when there is any sort of viable alternative.
"Never lie to your metallurgist"- TWT
woodsy
Blackhawk
Posts: 668
Joined: Thu Jan 05, 2012 9:03 pm
Location: Seymour, CT

Re: What Would You Do?

Post by woodsy »

If it had two prior owners I could not assume that Ruger actually screwed it up during assembly. It may have been bubba'd before you got it.
And a simple phone call to Ruger, armed with appropriate questions about their remedy, would be a good start.
LDB
Bearcat
Posts: 56
Joined: Wed Oct 17, 2012 3:00 pm
Location: Houston suburb

Re: What Would You Do?

Post by LDB »

I'd probably contact Ruger and make sure no matter what they would return that specific gun with S/N whatever it is to me. If yes, I'd send it to them. I've heard a lot of good reports on their NC (I think it is) facility so I'd probably try to send it there.
Support the entire Constitution, not just the parts you like.
Common sense is only right wing if you are too far to the left.
Hondo44
Hawkeye
Posts: 7648
Joined: Fri Apr 03, 2009 7:01 pm
Location: People's Republik of California

Re: What Would You Do?

Post by Hondo44 »

Once the head breaks off of a screw, there's no tension on it and the broken piece usually screws out easily without special tools or left handed drill bits.

You can try a small pointed center punch at an angle and attempt to turn the screw out with counter clockwise tiny hammer taps near the edge.

Or if that doesn't do it, you can even gently punch a line of dots forming a screw slot. Then try a small screwdriver to unscrew it.

If you call Ruger, ask if they will remove a broken screw or junk the frame?
Jim
Ruger single action "collector, accumulator, builder and shooter"
NRA Life
CRPA Life
CRPC Life
SASS Life
SWCA
RCA
professor_cassidy
Bearcat
Posts: 60
Joined: Sun Sep 07, 2008 7:45 pm
Location: Virginia

Re: What Would You Do?

Post by professor_cassidy »

Thanks everyone for your replies. Unfortunately the only good/real gunsmith in my
area passed away over 30 years ago. I’ll let you know how this turns out.
8) or :cry:
jgt
Buckeye
Posts: 1381
Joined: Wed Jul 30, 2008 11:51 am

Re: What Would You Do?

Post by jgt »

I would call Ruger and order two replacement screws for the grip frame. One to replace the headless one and one for the over torqued one. They will probably send them free of charge as customer service, but if not, you would still have the correct ones on hand.
Hondo44
Hawkeye
Posts: 7648
Joined: Fri Apr 03, 2009 7:01 pm
Location: People's Republik of California

Re: What Would You Do?

Post by Hondo44 »

Ruger will send any parts under ~$20 free of charge: (336) 949-5200. Be prepared to give them the serial # of the gun for reference if you call.
Jim
Ruger single action "collector, accumulator, builder and shooter"
NRA Life
CRPA Life
CRPC Life
SASS Life
SWCA
RCA
professor_cassidy
Bearcat
Posts: 60
Joined: Sun Sep 07, 2008 7:45 pm
Location: Virginia

Re: What Would You Do?

Post by professor_cassidy »

Talked to a local gunsmith today, said he could take a look at it in 2-3 months.
Called Ruger and got a return shipping label. Sending back tomorrow and hoping
for the best. We’ll see.
:D :(
George
Blackhawk
Posts: 742
Joined: Mon Jan 28, 2013 12:28 pm
Location: New Hampshire,"live free or die"

Re: What Would You Do?

Post by George »

Don't forget to mention the hammer transfer bar pinch when you send it back 2 Ruger! The Hammer needs to be filled down in the proper area. The transfer bars are metal injected molded parts and are usually pretty consistent! I had to do that with the 44 that had was a Lipsys addition. Didn't even have to take the gun apart! Really easy to do! Good luck! Let us know how you make out! George
woodsy
Blackhawk
Posts: 668
Joined: Thu Jan 05, 2012 9:03 pm
Location: Seymour, CT

Re: What Would You Do?

Post by woodsy »

professor_cassidy wrote:Talked to a local gunsmith today, said he could take a look at it in 2-3 months.
Called Ruger and got a return shipping label. Sending back tomorrow and hoping
for the best. We’ll see.
:D :(

Any updates?
professor_cassidy
Bearcat
Posts: 60
Joined: Sun Sep 07, 2008 7:45 pm
Location: Virginia

Re: What Would You Do?

Post by professor_cassidy »

Gun is at Ruger, received this email on the 15th:

"Dear Valued Ruger Customer,

We have received your Ruger firearm and are reviewing your concerns. We will work hard to address
your concerns and get back to you quickly. Our typical response time is less than one week, but we will
update you along the way so that you can track the process."

Hoping to hear more this week 8)
professor_cassidy
Bearcat
Posts: 60
Joined: Sun Sep 07, 2008 7:45 pm
Location: Virginia

Re: What Would You Do?

Post by professor_cassidy »

This story has a happy ending! I received my revolver back from Ruger this morning and they did remove the broken screw and replaced all the grip screws. They also replaced the front sight which wobbled a little front to back. I didn’t mention transfer bar pinch because with the factory “200lb” trigger spring with both legs attached it was powerful enough to suck the transfer bar down. Unfortunately this leaves a creepy 5lb trigger pull.
Even with the creepy heavy trigger I managed to get some good groups this afternoon while testing the gun with a cast 255gr SWC, 9.0grs Unique in the 45 Colt cylinder and Winchester 230gr JHP factory loads in the 45ACP cylinder.

This has been my most satisfying contact with Ruger Customer Service in 40+ years.
It only took 2 1/2 weeks from sending to them and receiving the gun back.

Next up is some work on the transfer bar and trigger spring. Then I can really live happily ever after. 8) :D
contender
Ruger Guru
Posts: 38050
Joined: Wed Sep 18, 2002 1:01 am
Location: Lake Lure NC USA

Re: What Would You Do? Updated 10/25/21

Post by contender »

Sounds good!
Shoot straight and safe!

" A fine is a tax for doing wrong,
and a tax is a fine for doing
right! "
NRA Instructor
USPSA shooter
SASS shooter (Outlaw Joe Wales)
NRA Women On Target Instructor
NC Hunter Safety Instructor
Nuisance Wildlife Control
Scuba Instructor
Eagle Scout, BSA "When it mattered!"
Dave P.
Buckeye
Posts: 1571
Joined: Wed Apr 02, 2014 3:40 pm

Re: What Would You Do? Updated 10/25/21

Post by Dave P. »

I bought one of the limited run Turnbull color case hardened .45s a few years ago
and the trigger was pretty bad. Ordered a hammer and trigger kit from Power customs,
after installing and "tuning" it a bit I have a trigger with about .020 of travel before the break,
at about 2.5 pounds.
As a plus it was available in a black oxide finish ( not real blue ) but looks to me a lot
better than the stainless hammer that Ruger installed.
Dry firing will sometimes allow the transfer bar to stick, but it never happens with live ammo.
It would be an easy adjustment to correct it but I've never bothered and sorta forgot about
it till I read this thread.
Added a Belt Mountain base pin and cleaned up the bore in the cylinder for the pin.
The bore looked like it had been "machined" by a rodent with buck teeth!
Dave
Post Reply