RugerForum.com
http://www.rugerforum.com/phpBB3/

The .357 Hunter
http://www.rugerforum.com/phpBB3/viewtopic.php?f=3&t=250398
Page 3 of 3

Author:  Joe S. [ Sat Oct 20, 2018 9:28 pm ]
Post subject:  Re: The .357 Hunter

s4s4u wrote:
I think it might make a good candidate to punch out to 360 DW



I was thinking 356 GNR!

Author:  sergeant206 [ Sun Oct 21, 2018 2:30 am ]
Post subject:  Re: The .357 Hunter

I am in for a 357 hunter with plow handle frame!

Author:  ChiefTJS [ Sun Oct 21, 2018 5:51 am ]
Post subject:  Re: The .357 Hunter

A year later and I would still buy two of them and want one just as bad now as I did then. I've got a rack full of .357's and still feel a Ruger Hunter would fit right in and I think there's a whole lot of .357 shooters who would agree.

Author:  SBH4628 [ Mon Oct 22, 2018 5:07 pm ]
Post subject:  Re: The .357 Hunter

I would buy one

Author:  Buckeye Bill [ Sat Oct 27, 2018 11:04 pm ]
Post subject:  Re: The .357 Hunter

I hope that you will be able to get a limited run and you get one or two.

I feel like I have this covered with my Bisley 357 7.5 inch.

Best Trigger I have in my collection. If I can see it, I can hit it. Well, eventually.

Image

Bill

Author:  SteelBlue [ Mon Oct 29, 2018 9:00 am ]
Post subject:  Re: The .357 Hunter

If Ruger made a .357 Hunter you'd have hundreds of posts saying "I'd buy one if only" (they made it in blued finish, they made it in an 8-shot cylinder, they made it with a 10.5" barrel, they made it in a Bisley). And very few would actually buy one.

Author:  57springer [ Mon Oct 29, 2018 7:30 pm ]
Post subject:  Re: The .357 Hunter

SteelBlue wrote:
If Ruger made a .357 Hunter you'd have hundreds of posts saying "I'd buy one if only" (they made it in blued finish, they made it in an 8-shot cylinder, they made it with a 10.5" barrel, they made it in a Bisley). And very few would actually buy one.

:lol: :lol: :lol:

Author:  bogus bill [ Mon Oct 29, 2018 8:47 pm ]
Post subject:  Re: The .357 Hunter

Didn't ruger quit making the .357 Maximum due to a flame cutting problem on the top strap?

Author:  majorKAP [ Mon Oct 29, 2018 9:45 pm ]
Post subject:  Re: The .357 Hunter

A 360DW cylinder can be fitted into the standard Blackhawk frame. That would provide for three great cartridges from one gun.

Image

Author:  majorKAP [ Mon Oct 29, 2018 9:59 pm ]
Post subject:  Re: The .357 Hunter

[quote="bogus bill"]Didn't ruger quit making the .357 Maximum due to a flame cutting problem on the top strap?[/quote]


More so, I think primarily, it was a handloader problem in trying to reach ultra velocities using lightweight bullets. Secondarily, it was a problem due to a few gunwriters of the day crying like Chicken Little. The guns didn't fail, in spite of a bit of "flame-cutting". That's why lot's of us are still shooting them today. But, then again, it's only my opinion.

Author:  bogus bill [ Mon Oct 29, 2018 10:23 pm ]
Post subject:  Re: The .357 Hunter

Thanks majorKAP.

Author:  Missedagain [ Tue Jun 11, 2019 3:25 pm ]
Post subject:  Re: The .357 Hunter

Still emailing the CEO and still waiting. I’d still buy one in a heart beat.

Author:  mohavesam [ Tue Jun 11, 2019 6:34 pm ]
Post subject:  Re: The .357 Hunter

Heck, we all asked for a 32 Hunter (loudly) for years. Just a few replies of why it couldn't be done. ?

Truth is...

Author:  Kevin [ Wed Jun 12, 2019 6:15 am ]
Post subject:  Re: The .357 Hunter

Hey, I’ll take one too! Stainless Bisley with the cut outs for a scope please.

I didn’t count but how many so far, 15 or 20 after 2 years for this thread? :D I bet they would sell. The 357 mag is such a popular caliber. Probably 22 LR and 357 mag are the most sold.

Author:  Joe S. [ Wed Jun 12, 2019 8:05 am ]
Post subject:  Re: The .357 Hunter

If they make em i hope they offer a 9mm cylinder so we can get it reamed for 36” DW or 356 GNR OR 357/44

Page 3 of 3 All times are UTC - 7 hours [ DST ]
Powered by phpBB® Forum Software © phpBB Group
http://www.phpbb.com/