RugerForum.com

This is a Ruger Firearms enthusiast's forum, but it is in no way affiliated with, nor does it represent Sturm Ruger & Company Inc. of Southport, CT.
It is currently Thu Dec 12, 2019 4:29 pm

All times are UTC - 7 hours [ DST ]




Post new topic Reply to topic  [ 5 posts ] 
Author Message
PostPosted: Tue Jul 23, 2019 8:48 am 
Buckeye
User avatar

Joined: Thu Oct 18, 2012 3:04 pm
Posts: 1920
Location: Ct., Va., & Vanzant, Mo.
i cant take no for an answer. ive been searching for years. there has to be something out there, or someone with the knowledge of repairing a plastic fused spacer crack on a rubber butt pad. the area where its cracked is in the classic high stress area of the toe. either it was snagged on a gun rack, over tightened, or dropped. ive seen many like this. and the answer i always get is...must be replaced or it will just crack again.
who out there has a secret repair method for this?
it is one of the hardest repairs ive ever encountered, that always tends to leave 'smiths stumped. any old timers know any tricks? anyone want to take it on? ive had suggestions to drill and pin, glue, remelt with a soldering gun, etc.... i need a for certain, done it a million times, works like a champ answer. lmk. and thanks in advance.
Image

_________________
Retired Military Aviation
Navy Distinguished Pistol Shot
Range Owner:
http://www.vanzantclaypigeonfarm.webs.com


Top
 Profile  
 
PostPosted: Fri Jul 26, 2019 11:35 am 
Single-Sixer

Joined: Thu Sep 04, 2008 6:50 pm
Posts: 165
Location: Tucson,AZ
Well,,, sometimes NO is the correct answer.
Rubber and plastic are compounds that have a lifespan. Drying ,warping and shrinkage are the enemies . Older compounds seem to have shorter lifespans and when it is over ,,,,,it's over.
Fight that windmill if you must but any attempt at preservation involving glue, melting , fillers or some such will look like Bubba gone wild and be short lived. Would you attempt to repair your car tires when they crack ?
Looks like a nice rifle so give it the respect it deserves. Replace it and go shoot it.


Top
 Profile  
 
PostPosted: Tue Jul 30, 2019 10:25 am 
Single-Sixer

Joined: Thu Feb 11, 2016 3:54 pm
Posts: 117
Epoxying the pad into place would work but if it is old enough to crack the "spacer" I would imagine that the pad material has seen better days as well.

Me, I'd simply replace it.


Top
 Profile  
 
PostPosted: Wed Aug 07, 2019 7:56 pm 
Bearcat

Joined: Wed Jan 20, 2016 6:18 pm
Posts: 28
Bobski,

I had a Model 50 Trap gun that the pad was cracked just like the one in the picture and I tried everything from glue to epoxying a thin steel strip the entire length of the pad and it always cracked again. I ended up buying one of the aftermarket pads from Brownell's that were copies of the original pad.

Mike


Top
 Profile  
 
PostPosted: Thu Sep 12, 2019 11:01 am 
Buckeye

Joined: Sun Mar 23, 2008 2:51 pm
Posts: 1586
Location: SW Oregon
I'm sorry to say, "replace it."


Top
 Profile  
 
Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 5 posts ] 

All times are UTC - 7 hours [ DST ]


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum

Search for:
Jump to:  
Powered by phpBB® Forum Software © phpBB Group