12ga,10ga,8ga,4ga FH; 585HE/700HE; Other Big Bores--

20mm Vulcan is a big case that works ok, without having

the sides made too thick...They have thinner sides

than smaller cases guys are getting that have the sides

made too thick and won't extract easy or work with high pressures.


Here Barnard P Cheytac bolt that would do for our 416 HSM..Ed......

Got guys doing various 416 HEs..

One just built a 416 HE, just been testing it a few days..

And using 168gr of HBMG 475 gr CEB, tested it, in good

conditions, 2 shots at 1800 yards and was within

a 1/4 of minute accuracy...A few shots at shorter ranges

had same accuracy. Ed..

More about our 416 HSM from BMG brass, and
our 416 HE & 460 HE from our 585 HE cases
Got reamers for 375 HE, 416 HE and 416 HSM,....

460 HE & 460 HSM are all spec'd, got HE reamer
soon have HSM reamer...Our HSMs have a Wea type
radius on the shoulder..

The fellow that set up our 416 HE in an ELR rifle
and got 1/4 min accuracy,
They got some game out west over 1400 yds..
.Here is the gun they set up.
Using a K&P 34" barrel on a BAT action.....Ed

And have got 460 HSM specs setup, the impetus for that is some
asking about one and new great line of 458 bullets CEB now has.

It will hold more powder than the 416 HSM and will get
a 572 gr as fast as 416 HSM gets a 475gr.....Ed..

The guys that did the super accurate 416 HE did another
416 HE that has an 8" longer 42 inch K&P barrel..

Used a Stiller action and same load with 475 gr bullet, as in
first gun and and gained about 200 fps with good accuracy.
3065 fps. Tested 2 groups of 3 and less than 1/2 min moa.

And loads they used are not the highest speed loads
the cartridge is capable of....Here is print with specs for
the 416 HE reamer chamber ....Ed....

More about he guys that did the accurate 416 HE, they did a
416 HE that has an 8" longer 42 inch K&P barrel..

Used longer barrel and the same load with 475 gr bullet, as used
in the first gun and and gained about 200 fps with good accuracy,.
3065 fps. Tested 2 groups of 3 and less than 1/2 min moa.

And loads they used are not the highest speed loads
the cartridge is capable of....Here is picture.......Ed....

Away for a time, sickness..
Here is print with chamber reamer specs for the
416 HSM chamber..There are 3 base sizes we have,
depending on actions used. Got reamers for all 3..
Got cases for all of them..
Our cases are public domain, so that is why I post
info and specs. To help guys do their own setups.
Manson makes reamers I use,,, Ed.

Here is reamer print with chamber reamer specs for
the 460 HSM chamber .Couple guys getting set
to do 38-40 inch heavy 458 target barrels...Ed....

With 40 inch barrel 416 HSM ,475 gr, get 3650, over 13,000 ft lbs muzzle energy.
Got guys getting set to have 38-40 inch 458 barrels made for 460 HSM.Ed..

More info on this gun, we did it for testing 416 HSM with a rebated rim,
to check in intermediate size actions, with the longer, stronger, bolt lugs, Ed..

Here is experimental action for 416 HSM in a heavy
stock....We lengthened port a little, set bolt stop back ,
opened bolt face fit the 416 HSM rebated rim. Ed.

Here is comparison of Montana PH to Pierce action we
modified to use for rebated rim 416 HSM testing..Ed.

416 & 460 HE AND 416 & 460 HSM .LONG RANGE AND HUNTING
Can be set up in  Pierce  X10  ACTION for the 416 & 460 HE  
And Ruger and Enfields..
AND X20 action for the 416 & 460 HSM , Can get those
if guys need one...Ed

Here is picture of my 416 HSM test gun,... It is a big falling block we had
as a 8 bore years ago. Has a 34 inch , 1 5/8 "diameter, 1 to 10 twist barrel. .. Ed.